OBJS2 |
Monday, August 18, 2003 | E200050 |
System Component, Electrical Insulation -Component | ||
P.LEO & CO. LTD. | ||
PO BOX 94250 RICHMOND BC V6Y 2A6 CANADA |
System Component: |
System
|
System
Temp (Class) |
System Maximum Voltage |
1G006, 1G015, 1G027, 1G155, 1G180, 1G2130, 1H75A, 1K063, 1K7170, 1K7177, 1K7270, 1M868, 1N008, 1N012, 1P130, 1P700, 1P702, 1P707, 1P717, 1P9FR, 1PG880, 1PG887, 1PK825, 1PN828, Non-adhesive woven glass tape, PTFE Tube 2T-TFL, PTFE Tube 2T-TFT, Silicone Coated Fiberglas 2R-SG |
HV-2 |
220(R) |
34.5 KV |
Underwriters Laboratories Inc. |
Construction Details (Table I) |
The use of this insulation system is limited to the combination of materials specified below. Where more than one item is designated under Insulation Function, they may be used together, unless otherwise indicated, or they may be used as alternates to one another. Functions designated "optional" are not necessarily required for every design. Insulation thicknesses and/or layers indicated below are minimum. |
Note: Coil to be helical or "strap" barrel wound only. Low Voltage Layer Insulation (Optional) and End Fill (Optional) can be any material in this table. |
Magnet Wire Insulation - Recognized Component - Magnet wire (OBMW2), single build or greater. |
(unless otherwise noted, magnet wire types listed below may be used in combination within a single product) |
Dupont | ||
Nomex 410 or 414 |
5 mils (0.13 mm) 50 percent overlap |
Bare Conductor - Bare sheet aluminum or copper to be covered with one layer of 5 mils nominal, 4.5 mils min. thickness Aramid paper, Nomex 410 or 414 |
Ground & Interwinding Insulation | |||
|
Designation (No.) |
mils(mm) |
Comments |
DuPont | |||
Nomex 410 or 414 |
10 (0.25) |
| |
| |||
Nomex 411 |
195.5 (4.97) |
0.016 min. thickness | |
E. I. Dupont de Nemours & Co. | |||
Nomex 411 |
58.7 (1.49) |
aramid insulating paper |
Lead Wire (optional) |
200C PTFE - polytetrafluoroethylene + | |
200C SI - silicone rubber - with or without glass braid + |
+ - |
To be isolated from direct contact with windings (magnet wire) by any insulating |
material (tape, layer insulation, sleeving,etc.) listed in this table - unless specifically excluded from this requirement by a special note at the beginning of this table. |
Minor Sheet Insulation (optional) layer, outer, wrap, etc. | ||
|
Designation (No.) |
Comments |
| ||
Kapton 100HA |
Minor Sheet Insulation Materials may be used to supplement but not to replace the above nonoptical materials. |
| ||
Kapton 100HN |
|
| ||
Kapton 100PST |
|
| ||
Kapton 100V |
|
| ||
Kapton 100VN |
|
| ||
Kapton 100XFPC |
|
Innovative Paper Technologies, LLC (Quin-T Corp.) | ||
CeQuin 3000 |
|
| ||
CeQuin I |
|
| ||
CeQuin IF, IFI, FIF |
|
| ||
CeQuin IG, IGI, GIG |
|
| ||
CeQuin II |
|
| ||
CeQuin V |
|
| ||
CeQuin VF, VFV, FVF |
|
| ||
CeQuin VG, VGV, GVG |
|
| ||
CeQuinbord CGA |
|
| ||
TufQuin 110, 120 |
|
| ||
TufQuin TF, TFT, FTF |
|
Midwest Mica Co. | ||
03-02-32 |
|
Tapes (optional) | ||
|
Designation (No.) |
Comments |
P.LEO & CO. LTD. | ||
1G006 |
aramid fiber (Nomex) paper |
| ||
1G015 |
silicone adhesive, glass cloth |
| ||
1G027 |
rubber adhesive, glass cloth |
| ||
1G155 |
glass cloth |
| ||
1G180 |
glass cloth |
| ||
1G2130 |
|
| ||
1H75A |
|
| ||
1K063 |
silicone adhesive, polyimide film |
| ||
1K7170 |
Kapton film |
| ||
1K7177 |
Kapton film |
| ||
1K7270 |
Kapton film |
| ||
1M868 |
|
| ||
1N008 |
aramid fiber (Nomex), rubber adhesive |
| ||
1N012 |
Nomex Tape, Acrylic adhesive |
| ||
1P130 |
acrylic adhesive, polyester film |
| ||
1P700 |
polyester film |
| ||
1P702 |
polyester film |
| ||
1P707 |
polyester film |
| ||
1P717 |
polyester film |
| ||
1P9FR |
|
| ||
1PG880 |
|
| ||
1PG887 |
|
| ||
1PK825 |
|
| ||
1PN828 |
|
Various Manufacturers | ||
Non-adhesive woven glass tape |
|
Spacers, Wedges (optional) | ||
|
Designation (No.) |
Comments |
Electro Isola | ||
XX |
|
Glastic Corp. | ||
FHT |
|
| ||
MTS |
|
Haysite | ||
HST-II |
glass reinforced thermosetting polyester |
| ||
HTF |
flexible, glass reinforced thermosetting polyester |
Liberty Polyglas | ||
Polyglas |
|
| ||
Supersil |
|
National Vulcanized Fiber | ||
Lamicor GP-200HT |
|
| ||
Lamicor GP9701 |
|
Nohl | ||
NRT-200 |
|
| ||
NRT-220 |
|
Phillips Petroleum Co. | ||
Ryton R-4 |
|
| ||
Ryton R-7 |
|
Sleevings (optional) | ||
|
Designation (No.) |
Comments |
Bentley-Harris | ||
Acryl |
|
| ||
Ben-Har 1151-XL-200 |
|
| ||
Ben-Har 1151-XL-220 |
|
| ||
Ben-Har 1151-XL-FR-1 |
|
| ||
Ben-Har Ex-Flex |
|
| ||
Ben-Har Teflon TFE |
|
| ||
Ber-Har 1151-XL-240 |
|
| ||
E |
|
| ||
ST |
|
| ||
ST-1250 |
|
Essex | ||
Acrylflex |
|
| ||
Acrylflex VPI |
|
| ||
Suflex Flexicone 200 |
|
| ||
Suflex Silverflex |
|
| ||
Suflex Silverflex T+D |
|
Hilec (Brand Rex, Voltube) | ||
Turbo TUF |
|
| ||
Turbo 117 |
|
Nichias | ||
9003-150@ |
|
P. Leo | ||
PTFE Tube 2T-TFL |
|
| ||
PTFE Tube 2T-TFT |
|
| ||
Silicone Coated Fiberglas 2R-SG |
|
Stone Industrial | ||
Nomex/Mylar Tube |
|
Varflex | ||
Varglas Non-Fray Type H |
|
| ||
Varglas Non-Fray Type HM |
|
| ||
Varglas Non-Fray Type HO |
|
| ||
Varglas Non-Fray Type HP |
|
| ||
Varglas Silicone Rubber |
|
| ||
Varglas Silicone Rubber 500 |
|
| ||
Varglas Viton 231 |
|
Tie Cords (optional) | ||
|
Designation (No.) |
Comments |
Atkins and Pearce | ||
MS 9023-T4 |
|
| ||
13-220 |
|
Hilec (Brand Rex, Voltube) | ||
SC |
|
Varflex | ||
46 |
silicone coated fiberglass |
| ||
48 |
silicone coated fiberglass |
Various Manufacturers | ||
Fiberglass, untreated |
|
Western Filament | ||
DHS Series |
|
| ||
DPS Series |
|
| ||
DRT Series |
|
| ||
EM2C |
|
| ||
50DOF17W |
|
Varnishes (optional) Recognized Component - Varnishes (OBOR2) | ||
|
Designation (No.) |
Comments |
Ripley Resin Engineering Co Inc | ||
468-2(+) |
(+) may be proceed by prefix "E" and may be followed by a one to five alphanumeric suffix indicating % inert filler and/or color |
| ||
468-2-7(++) |
(++) may be followed by a one or two character suffix indicating % inert filler or color. |
| ||
468-2FC(++) |
(++) may be followed by a one or two alphanumeric suffix indicating % inert filler and/or color |
Miscellaneous Minor Insulations (optional) | ||
|
Designation (No.) |
Comments |
Epoxylite Corp. | ||
223 |
Adhesive |
| ||
810 |
Adhesive |
| ||
8811 |
|
| ||
8899 |
Adhesive |
NOTICE : This information , based upont UL Testing Guidelines and our experience, is offered without charge by P. Leo as part of our service to customers. It is intended for persons having technical skill to use at their own discretion and risk. We do not guarantee favorable results, and the P.LEO & CO. LTD. assumes no obligation or liability for any advice furnished or for any results obtained to operae under, or a recommendation to infringe upon, any patent of P. Leo or others. Compliance with applicable government codes is also the responsibility of the user.